diff options
Diffstat (limited to 'doc/imrelp.html')
| -rw-r--r-- | doc/imrelp.html | 53 |
1 files changed, 46 insertions, 7 deletions
diff --git a/doc/imrelp.html b/doc/imrelp.html index f7fcc4b3..73af2659 100644 --- a/doc/imrelp.html +++ b/doc/imrelp.html @@ -28,14 +28,54 @@ nits outlined above, is a much more reliable solution than plain tcp syslog and so it is highly suggested to use RELP instead of plain tcp. Clients send messages to the RELP server via omrelp.</p> -<p><b>Configuration Directives</b>:</p> +<p><b>Module Parameters</b>:</p> +<ul> + <li><b>Ruleset</b> <name></br> + Binds the specified ruleset to <b>all</b> RELP listeners. +</ul> +<p><b>Input Parameters</b>:</p> <ul> <li><b>Port</b> <port><br> Starts a RELP server on selected port</li> +<li><b>tls</b> (not mandatory, values "on","off", default "off")<br> +If set to "on", the RELP connection will be encrypted by TLS, +so that the data is protected against observers. Please note +that both the client and the server must have set TLS to +either "on" or "off". Other combinations lead to unpredictable +results. +</li> +<li><b>tls.compression</b> (not mandatory, values "on","off", default "off")<br> +The controls if the TLS stream should be compressed (zipped). While this +increases CPU use, the network bandwidth should be reduced. Note that +typical text-based log records usually compress rather well. +</li> +<li><b>tls.dhbits</b> (not mandatory, integer)<br> +This setting controls how many bits are used for Diffie-Hellman key +generation. If not set, the librelp default is used. For secrity +reasons, at least 1024 bits should be used. Please note that the number +of bits must be supported by GnuTLS. If an invalid number is given, rsyslog +will report an error when the listener is started. We do this to be transparent +to changes/upgrades in GnuTLS (to check at config processing time, we would need +to hardcode the supported bits and keep them in sync with GnuTLS - this is +even impossible when custom GnuTLS changes are made...). +</li> +<li><b>tls.prioritystring</b> (not mandatory, string)<br> +This parameter permits to specify the so-called "priority string" to +GnuTLS. This string gives complete control over all crypto parameters, +including compression setting. For this reason, when the prioritystring +is specified, the "tls.compression" parameter has no effect and is +ignored. +<br>Full information about how to construct a priority string can be +found in the GnuTLS manual. At the time of this writing, this +information was contained in +<a href="http://gnutls.org/manual/html_node/Priority-Strings.html">section 6.10 of the GnuTLS manual</a>. +<br><b>Note: this is an expert parameter.</b> Do not use if you do +not exactly know what you are doing. +</li> </ul> <b>Caveats/Known Bugs:</b> <ul> -<li>ruleset can only be bound via legacy configuration format</li> +<li>see description</li> <li>To obtain the remote system's IP address, you need to have at least librelp 1.0.0 installed. Versions below it return the hostname instead of the IP address.</li> @@ -45,20 +85,19 @@ not specific ones. This is due to a currently existing limitation in librelp. <p><b>Sample:</b></p> <p>This sets up a RELP server on port 20514.<br> </p> -<textarea rows="15" cols="60">module(load="imrelp") # needs to be done just once +<textarea rows="5" cols="60">module(load="imrelp") # needs to be done just once input(type="imrelp" port="20514") </textarea> <p><b>Legacy Configuration Directives</b>:</p> <ul> <li>InputRELPServerBindRuleset <name> (available in 6.3.6+)</br> -Binds the specified ruleset to all RELP listeners. +equivalent to: RuleSet <li>InputRELPServerRun <port><br> equivalent to: Port</li> </ul> <b>Caveats/Known Bugs:</b> <ul> -<li>see description</li> <li>To obtain the remote system's IP address, you need to have at least librelp 1.0.0 installed. Versions below it return the hostname instead of the IP address.</li> @@ -68,14 +107,14 @@ not specific ones. This is due to a currently existing limitation in librelp. <p><b>Sample:</b></p> <p>This sets up a RELP server on port 20514.<br> </p> -<textarea rows="15" cols="60">$ModLoad imrelp # needs to be done just once +<textarea rows="5" cols="60">$ModLoad imrelp # needs to be done just once $InputRELPServerRun 20514 </textarea> <p>[<a href="rsyslog_conf.html">rsyslog.conf overview</a>] [<a href="manual.html">manual index</a>] [<a href="http://www.rsyslog.com/">rsyslog site</a>]</p> <p><font size="2">This documentation is part of the <a href="http://www.rsyslog.com/">rsyslog</a> project.<br> -Copyright © 2008-2011 by <a href="http://www.gerhards.net/rainer">Rainer +Copyright © 2008-2013 by <a href="http://www.gerhards.net/rainer">Rainer Gerhards</a> and <a href="http://www.adiscon.com/">Adiscon</a>. Released under the GNU GPL version 3 or higher.</font></p> |