diff options
Diffstat (limited to 'doc')
| -rw-r--r-- | doc/imuxsock.html | 28 | ||||
| -rw-r--r-- | doc/manual.html | 2 | ||||
| -rw-r--r-- | doc/rsyslog_conf_global.html | 4 |
3 files changed, 31 insertions, 3 deletions
diff --git a/doc/imuxsock.html b/doc/imuxsock.html index 472470a0..15c365a6 100644 --- a/doc/imuxsock.html +++ b/doc/imuxsock.html @@ -46,6 +46,18 @@ Ignore timestamps included in the messages, applies to messages received via the <li><b>$SystemLogSocketName</b> <name-of-socket> -- former -p option</li> <li><b>$SystemLogFlowControl</b> [on/<b>off</b>] - specifies if flow control should be applied to the system log socket.</li> +<li><b>$InputUnixListenSocketCreatePath</b> [on/<b>off</b>] - create directories in the socket path +if they do not already exist. They are created with 0755 permissions with the owner being the process under +which rsyslogd runs. The default is not to create directories. Keep in mind, though, that rsyslogd always +creates the socket itself if it does not exist (just not the directories by default). +<br>Note that this statement affects the +next $AddUnixListenSocket directive that follows in sequence in the configuration file. It never works +on the system log socket (where it is deemed unnecessary). Also note that it is automatically +being reset to "off" after the $AddUnixListenSocket directive, so if you would have it active +for two additional listen sockets, you need to specify it in front of each one. This option is primarily considered +useful for defining additional sockets that reside on non-permanent file systems. As rsyslogd probably starts +up before the daemons that create these sockets, it is a vehicle to enable rsyslogd to listen to those +sockets even though their directories do not yet exist. [available since 4.7.0 and 5.3.0]</li> <li><b>$AddUnixListenSocket</b> <name-of-socket> adds additional unix socket, default none -- former -a option</li> <li><b>$InputUnixListenSocketHostName</b> <hostname> permits to override the hostname that shall be used inside messages taken from the <b>next</b> $AddUnixListenSocket socket. Note that @@ -57,20 +69,32 @@ that the local hostname can be overridden in cases where that is desired.</li> <br> This documentation is sparse and incomplete. <p><b>Sample:</b></p> -<p>The following sample is the minimum setup required to accept syslog messages from applications running on the local system.<br> +<p>The following sample is the minimum setup required to accept syslog messages from applications running +on the local system.<br> </p> <textarea rows="2" cols="70">$ModLoad imuxsock # needs to be done just once $SystemLogSocketFlowControl on # enable flow control (use if needed) </textarea> <p>The following sample is a configuration where rsyslogd pulls logs from two jails, and assigns different hostnames to each of the jails: </p> -<textarea rows="6" cols="60">$ModLoad imuxsock # needs to be done just once +<textarea rows="6" cols="70">$ModLoad imuxsock # needs to be done just once $InputUnixListenSocketHostName jail1.example.net $AddUnixListenSocket /jail/1/dev/log $InputUnixListenSocketHostName jail2.example.net $AddUnixListenSocket /jail/2/dev/log </textarea> +<p>The following sample is a configuration where rsyslogd reads the openssh log +messages via a separate socket, but this socket is created on a temporary file +system. As rsyslogd starts up before the sshd, it needs to create the socket +directories, because it otherwise can not open the socket and thus not listen +to openssh messages. Note that it is vital not to place any other socket between +the $InputUnixListenSocketCreatePath and the $InputUnixListenSocketHostName.</p> +<textarea rows="6" cols="70">$ModLoad imuxsock # needs to be done just once + +$InputUnixListenSocketCreatePath on # turn on for *next* socket +$InputUnixListenSocketHostName /var/run/sshd/dev/log +</textarea> <p>[<a href="rsyslog_conf.html">rsyslog.conf overview</a>] [<a href="manual.html">manual index</a>] [<a href="http://www.rsyslog.com/">rsyslog site</a>]</p> <p><font size="2">This documentation is part of the diff --git a/doc/manual.html b/doc/manual.html index e1f7480e..52a8380e 100644 --- a/doc/manual.html +++ b/doc/manual.html @@ -19,7 +19,7 @@ rsyslog support</a> available directly from the source!</p> <p><b>Please visit the <a href="http://www.rsyslog.com/sponsors">rsyslog sponsor's page</a> to honor the project sponsors or become one yourself!</b> We are very grateful for any help towards the project goals.</p> -<p><b>This documentation is for version 4.5.2 (v4-beta branch) of rsyslog.</b> +<p><b>This documentation is for version 4.7.0 (v4-devel branch) of rsyslog.</b> Visit the <i><a href="http://www.rsyslog.com/doc-status.html">rsyslog status page</a></i></b> to obtain current version information and project status. </p><p><b>If you like rsyslog, you might diff --git a/doc/rsyslog_conf_global.html b/doc/rsyslog_conf_global.html index 50d83a50..74255c54 100644 --- a/doc/rsyslog_conf_global.html +++ b/doc/rsyslog_conf_global.html @@ -149,6 +149,10 @@ Usually that should not be a big issue, as the restart-type HUP can easily be re something along the lines of "/etc/init.d/rsyslog restart". </li> <li><a href="rsconf1_includeconfig.html">$IncludeConfig</a></li><li>MainMsgQueueCheckpointInterval <number></li> +<li><b>$LogRSyslogStatusMessages</b> [<b>on</b>/off] - If set to on (the default), +rsyslog emits message on startup and shutdown as well as when it is HUPed. +This information might be needed by some log analyzers. If set to off, no such +status messages are logged, what may be useful for other scenarios. <li>$MainMsgQueueDequeueSlowdown <number> [number is timeout in <i> micro</i>seconds (1000000us is 1sec!), default 0 (no delay). Simple rate-limiting!]</li> |