RELP Input Module

Module Name: imrelp

Author: Rainer Gerhards

Description:

Provides the ability to receive syslog messages via the reliable RELP protocol. This module requires librelp to be present on the system. From the user's point of view, imrelp works much like imtcp or imgssapi, except that no message loss can occur. Please note that with the currently supported relp protocol version, a minor message duplication may occur if a network connection between the relp client and relp server breaks after the client could successfully send some messages but the server could not acknowledge them. The window of opportunity is very slim, but in theory this is possible. Future versions of RELP will prevent this. Please also note that rsyslogd may lose a few messages if rsyslog is shutdown while a network conneciton to the server is broken and could not yet be recovered. Future version of RELP support in rsyslog will prevent that. Please note that both scenarios also exists with plain tcp syslog. RELP, even with the small nits outlined above, is a much more reliable solution than plain tcp syslog and so it is highly suggested to use RELP instead of plain tcp. Clients send messages to the RELP server via omrelp.

Module Parameters:

Ruleset <name>
Binds the specified ruleset to all RELP listeners.

Input Parameters:

Port <port>
Starts a RELP server on selected port
tls (not mandatory, values "on","off", default "off")
If set to "on", the RELP connection will be encrypted by TLS, so that the data is protected against observers. Please note that both the client and the server must have set TLS to either "on" or "off". Other combinations lead to unpredictable results.
tls.compression (not mandatory, values "on","off", default "off")
The controls if the TLS stream should be compressed (zipped). While this increases CPU use, the network bandwidth should be reduced. Note that typical text-based log records usually compress rather well.
tls.dhbits (not mandatory, integer)
This setting controls how many bits are used for Diffie-Hellman key generation. If not set, the librelp default is used. For secrity reasons, at least 1024 bits should be used. Please note that the number of bits must be supported by GnuTLS. If an invalid number is given, rsyslog will report an error when the listener is started. We do this to be transparent to changes/upgrades in GnuTLS (to check at config processing time, we would need to hardcode the supported bits and keep them in sync with GnuTLS - this is even impossible when custom GnuTLS changes are made...).
tls.prioritystring (not mandatory, string)
This parameter permits to specify the so-called "priority string" to GnuTLS. This string gives complete control over all crypto parameters, including compression setting. For this reason, when the prioritystring is specified, the "tls.compression" parameter has no effect and is ignored.
Full information about how to construct a priority string can be found in the GnuTLS manual. At the time of this writing, this information was contained in section 6.10 of the GnuTLS manual.
Note: this is an expert parameter. Do not use if you do not exactly know what you are doing.

Caveats/Known Bugs:

see description
To obtain the remote system's IP address, you need to have at least librelp 1.0.0 installed. Versions below it return the hostname instead of the IP address.
Contrary to other inputs, the ruleset can only be bound to all listeners, not specific ones. This is due to a currently existing limitation in librelp.

Sample:

This sets up a RELP server on port 20514.

Legacy Configuration Directives:

InputRELPServerBindRuleset <name> (available in 6.3.6+)
equivalent to: RuleSet
InputRELPServerRun <port>
equivalent to: Port

Caveats/Known Bugs:

To obtain the remote system's IP address, you need to have at least librelp 1.0.0 installed. Versions below it return the hostname instead of the IP address.
Contrary to other inputs, the ruleset can only be bound to all listeners, not specific ones. This is due to a currently existing limitation in librelp.

Sample:

This sets up a RELP server on port 20514.

[rsyslog.conf overview] [manual index] [rsyslog site]